spt-blog-banner-13-1

MEMS Sacrificial Etching: Comparing XeF₂ and Vapor HF

MEMS Sacrificial Etching: Comparing XeF₂ and Vapor HF

Sacrificial layer etching in MEMS manufacturing is the "release process" that frees movable microstructures from the substrate—a critical step that directly dictates device yield and performance. Today, liquid-free vapor-phase etching is the mainstream approach. The two leading methodologies, xenon difluoride (XeF₂ ) and vapor hydrogen fluoride (vapor HF), represent distinct dry-release methods with different target materials and unique technical challenges.

This article outlines the fundamentals of stiction encountered in wet release processes, details the characteristics and practical considerations of both dry methods, and provides a decision-making framework to help you select the optimal approach based on your device architecture.

What is Sacrificial Layer Etching? The Process of "Releasing" Movable MEMS Structures

Micro-Electro-Mechanical Systems (MEMS) integrate mechanical elements and electronic components onto a single silicon substrate. The global MEMS market was valued at USD 22.4 billion in 2025 and is projected to reach USD 49.8 billion by 2034, growing at a CAGR of 9.3%(Source:Dataintelo, "MEMS (Microelectromechanical Systems) Market Outlook 2025-2034").

In MEMS fabrication, a "sacrificial layer" is pre-patterned beneath the structural layers and subsequently removed in a selective etch step. This releases the movable parts from the substrate, creating freestanding, hollow cavities. Because this release step occurs at the very end of the process line—after all structural layers have already been defined—any defect here renders all prior processing steps obsolete. This makes sacrificial layer etching one of the most yield-critical steps in the entire fabrication flow.

The Shift from Wet to Vapor-Phase Etching

Historically, liquid chemical solutions (wet etching) were widely used for sacrificial layer release. However, capillary stiction—discussed below—proved to be a critical failure mode. For high-volume manufacturing (HVM), achieving rigorous process repeatability and high yields is essential, as emphasized by industry benchmarks such as SEMI’s MEMS Manufacturing Readiness Levels (MMRL) (Source:SEMI, "New SEMI MEMS Standard: Guide to MEMS Manufacturing Readiness Levels").
To fundamentally eliminate stiction, transitioning to dry, vapor-phase etching has become standard practice in MEMS mass production(Source:Solid State Phenomena, "Current Advances in Anhydrous HF/Organic Solvent Processing of Semiconductor Surfaces").

  • XeF₂ Gas Etching: Selectively removes Silicon (Si) as the sacrificial layer.

  • Vapor HF (VHF) Etching: Selectively removes Silicon Dioxide (SiO₂) as the sacrificial layer.

The distinction between these two processes is less about which is inherently "better" and more about architectural design: which material is designated as the sacrificial layer versus the structural layer.

Understanding Stiction: Structural Collapse in Wet Release

Stiction refers to the unintentional adhesion of suspended microstructures during the drying phase of wet etching, when the liquid transitions to gas. Capillary action creates immense surface tension that pulls flexible microstructures toward the substrate or adjacent features, causing them to adhere permanently. Stiction becomes exponentially more severe as the gap between the structure and the substrate narrows, leading to permanent device failure or mechanical destruction(Source:Solid State Phenomena).

Vapor-phase etching eliminates liquid surface tension at its source. However, in practice, simply using vapor does not guarantee an absence of stiction. As detailed later, trace moisture inside a vapor HF chamber can condense into localized liquid bridges, reintroducing stiction. The benefits of dry release can only be realized by strictly maintaining conditions where no liquid phase can form.

XeF₂ Sacrificial Etching: Highly Selective Removal of Silicon Sacrificial Layers

Reaction Mechanism and Selectivity

XeF₂ etching is a spontaneous, room-temperature chemical etch requiring no plasma ion bombardment, in which the reaction 2XeF₂+Si→2Xe+SiF₄ produces volatile silicon tetrafluoride (SiF₄ ) and xenon (Xe) as evacuated byproducts.

The most notable advantage of XeF₂ is its exceptionally high selectivity for silicon over silicon dioxide (SiO₂), silicon nitride (Si₃N₄), aluminum (Al), and standard photoresists. Reported Si:SiO₂ selectivity ratios exceed 1000:1, making it widely adopted for MEMS devices utilizing oxide or metal films as structural layers(Source:American Vacuum Society, "Silicon Etching in XeF2 Environment").

Regarding etch rates, instantaneous rates up to 19.5 µm/min have been reported in pulsed etching modes at an initial pressure of 1.2 Torr(Source:ResearchGate「Investigation and simulation of XeF₂ isotropic etching of silicon」). However, this represents an optimized peak rate; production processes must account for thermal effects and etch-rate distribution across the wafer.

Practical Consideration 1: Exothermic Reactions and Loading Effects

The reaction between XeF₂ and silicon is highly exothermic. When dealing with large exposed silicon areas or high reactant concentrations, localized thermal runaway on the wafer can occur. This heat causes thermal degradation of photoresist masks and destabilizes etch kinetics(Source:ResearchGate).

From a profile control standpoint, two phenomena are prominent (Source:American Vacuum Society).

  • Loading Effect: Neighboring etch regions compete for available reactant gas, causing local etch rate variations.

  • Trenching: Accelerated etching along pattern edges/boundaries.

Both effects complicate the uniform control of lateral undercut depths across the wafer.

Practical Consideration 2: The "Proximity Effect" Near SiO₂

While XeF₂ is theoretically inert toward SiO₂, recent studies demonstrate a "proximity effect": when exposed silicon lies adjacent to SiO₂, fluorine radicals generated during the Si–XeF₂ reaction diffuse outward and unintentionally attack the neighboring oxide(Source:ResearchGate, "Test Structure for Measuring the Selectivity in XeF2 and HF Vapour Etch Processes").

Under this effect, exposed oxide steps of 1 to 2 µm can be etched away, and thin oxide layers (50–100 nm) can disappear entirely even without exposed step edges(Source:ResearchGate, "XeF2-induced removal of SiO2 near Si surfaces at 300 K: An unexpected proximity effect"). Furthermore, trace moisture reacting with XeF₂ generates hydrofluoric acid (HF), introducing secondary oxide erosion(Source:JVST B / AVS).
Consequently, nominal bulk selectivities (>1000:1) cannot be taken for granted in microstructures where silicon and thin oxides sit side by side.

Vapor HF Sacrificial Etching: Balancing 
SiO₂ Removal with Metal Protection

Applicable Oxide Films and Process Architectures

Vapor HF (VHF) etching removes SiO₂ sacrificial layers, including thermal oxides, TEOS, and PECVD oxides. Processes typically employ either anhydrous HF (AHF) gas alone or AHF mixed with organic catalyst vapors (such as alcohol or glycerol)(Source:Solid State Phenomena).

Conventional aqueous HF wet solutions aggressively corrode aluminum (Al)—the primary metallization layer in standard CMOS circuitry. By strictly controlling an anhydrous vapor-phase environment, VHF isotropically etches SiO₂ while preserving aluminum interconnects. In systems combining anhydrous HF with oleum (fuming sulfuric acid), etch rates of approximately 1 µm/min for thermal oxide have been demonstrated while restricting the sheet resistance increase of aluminum structures to just 7.6% after a ~9-minute release (Source:ResearchGate, "Infinite Selectivity of Wet SiO2 Etching in Respect to Al").

Practical Consideration 1: Moisture Control Governs Yield

In CMOS-MEMS monolithic integration, residual chamber moisture or water generated as a reaction byproduct can form localized liquid capillary bridges within narrow gaps. This induces galvanic corrosion across heterogeneous metal boundaries and re-triggers stiction. Maintaining a strictly moisture-free process environment and rapidly evacuating reaction byproducts are absolute prerequisites for high-yield production(Source:Solid State Phenomena).

Additionally, non-optimized process recipes can lead to polymer residues from organic solvents or reaction byproducts, which can degrade mechanical resonance behavior and electrical isolation. VHF performance depends heavily on the tool's ability to manage moisture and exhaust byproducts.

Practical Consideration 2: Selecting Etch-Stop Materials

Investigations on etch-stop layers exposed to vapor HF reveal the following (Source:Fraunhofer IPMS ,"Etch stop materials for release by vapor HF etching").

  • Robust Resistance: Aluminum oxide (Al₂O₃) and aluminum fluoride (AlF₃) remain completely inert.

  • Caution Required: Silicon nitride (Si₃N₄) experiences partial attack, generating non-volatile residues.

While Si₃N₄ offers high selectivity in XeF₂ etching, it can act as a source of defect residues in vapor HF. This contrast must be accounted for during process integration.

Comparison Table: XeF₂ vs. Vapor HF

XeF₂ Gas Etching Vapor HF Etching
Target Material (Sacrificial Layer) Silicon (Si) Silicon Dioxide (SiO₂: Thermal, TEOS, PECVD, etc.)
Reaction Mechanism Spontaneous chemical reaction at room temperature; no plasma required Anhydrous HF alone or combined with organic solvent vapor
Selectivity Highlights High selectivity for Si over SiO₂, Si₃N₄, Al and photoresist(Si:SiO₂>1000:1) Isotropically removes SiO₂ while protecting Al metallization under strict anhydrous control
Typical Etch-Stop Materials SiO₂, Si₃N₄, Al, etc. Al₂O₃, AlF₃(Si₃N₄ exhibits slight etching and residue formation)
Key Technical Challenges Exothermic heat dissipation, loading effects, trenching, proximity effect, HF generation from trace moisture Moisture control (risk of Al corrosion and stiction recurrence), polymer residues
Reported Etch Rate Examples Up to 19.5 µm/min (Pulsed mode, initial pressure 1.2 Torr) Approx. 1 µm/min (Thermal oxide; anhydrous HF + oleum system)
 Note: References for numerical values and technical characteristics are detailed in the corresponding sections above. 

Application Criteria for Selecting the Right Sacrificial Release Method

Choosing between XeF₂ and vapor HF is driven by device design: what needs to be removed, and what must remain intact. Consider the following four criteria:

1:Sacrificial vs. Structural Layer Material Pairing:

If your design uses silicon as the sacrificial layer and oxide or metal as the freestanding structure, select XeF₂ . If silicon serves as the mechanical structure and SiO₂  acts as the sacrificial layer, choose vapor HF. For CMOS compatibility, utilizing interlayer dielectric (ILD) SiO₂ as the sacrificial release layer is often the preferred route.

2:Presence of Aluminum Metallization in CMOS-MEMS:

While XeF₂  is naturally selective against aluminum, vapor HF requires uncompromising moisture control to avoid aluminum corrosion. When opting for vapor HF, ensure the etching system maintains a robust, repeatable anhydrous environment.

3:Stacked Structures with Adjacent Si and SiO₂:

When exposed silicon directly neighbors SiO₂ , XeF₂ can induce proximity effects that erode thin oxide layers (tens to hundreds of nanometers). Conversely, vapor HF relies on removing oxide natively, making it immune to this specific failure mechanism.

4:Tool Architecture and Scalability to Mass Production:

Ensure that release recipes developed during R&D can transition seamlessly onto mass-production platforms. Equipment architectures should be evaluated based on long-term production scaling rather than laboratory-scale constraints alone.

Sacrificial Layer Etching Systems from Sumitomo Precision Products

Sumitomo Precision Products offers the "Vetelgeuse" sacrificial layer etching system, designed for vapor-phase anhydrous HF processes targeting SiO₂ release. Key highlights include:

  • Selective oxide removal without corrosive damage, even on devices incorporating aluminum microstructures.

  • A stable, condensation-free dry process preventing byproduct redeposition.

  • Proven undercut capability ranging from micro-scale features up to millimeter-scale cavities.

  • Production-proven track record across uncooled IR bolometers, cantilever beams, SOI wafer BOX layer release, and silicon resonators.

  • Built on the "VPX" cluster platform equipped with a central vacuum transfer robot (configurable with up to 3 process chambers), supporting 200 mm wafer processing from low-volume pilot runs to high-volume manufacturing (HVM).

Furthermore, Sumitomo Precision Products holds a 90% market share in Japan for Silicon DRIE systems, the primary front-end structuring step in MEMS fabrication. Our deep expertise spanning both deep silicon patterning and sacrificial release enables holistic process integration and optimization across your entire production line.

Summary

  • Sacrificial layer release is the critical final process that frees movable MEMS structures; vapor-phase etching has become the industry benchmark to eliminate stiction.

  • XeF₂​ delivers high selectivity for silicon sacrificial layers, though careful consideration must be given to exothermic heating, loading effects, and oxide proximity effects.

  • Vapor HF removes SiO₂ while preserving aluminum metallization, provided strict anhydrous conditions and residue management are enforced.

  • Method selection is dictated by material combinations, metallization requirements, adjacent stack geometries, and mass-production scaling roadmaps.

Disclaimer

The market data and statistics in this article reflect the information available at the time the cited sources were published. For the most current information, please refer to the official reports of the respective research organizations.
This page is a translation of the Japanese original. Some content may differ or reflect updates with a delay. For the most accurate and current information, please refer to the Japanese version as the official source.