You have completed the sacrificial layer etching, yet the movable microstructure remains stuck to the substrate and does not move. Have you ever struggled with this defect during MEMS development or mass production?
This phenomenon is known as stiction and represents one of the typical defects directly impacting MEMS manufacturing yields. However, the primary mechanisms behind stiction have been well-identified. By isolating the root causes step by step across the fabrication process, the appropriate countermeasures become clear.
This article explains why stiction occurs in wet processes and vapor HF processes, respectively. Furthermore, it outlines alternative countermeasures—such as advanced drying techniques and dry release—along with their prerequisites.
What Is a Sacrificial Layer?
A Layer Designed to Release Movable MEMS Microstructures from the Substrate
A sacrificial layer is positioned beneath a movable microstructure and is selectively removed via etching to mechanically decouple the structure from the substrate. Characteristic MEMS mechanical architectures—such as cantilevers, membranes, and bolometers—can only achieve mobility once this sacrificial layer is removed through a step called "release."
Silicon (Si) and silicon dioxide (SiO₂) are commonly used as sacrificial materials. Among them, SiO₂ is widely employed in MEMS processes as both an interlayer dielectric and a sacrificial layer. Releasing structures by removing the buried oxide (BOX) layer in SOI (Silicon-on-Insulator) wafers is also a typical example of SiO₂ sacrificial layer release
Why Defects in the Release Process Are Critical
Within the MEMS fabrication flow, the release process is the step where previously fabricated microstructures are finally set free. If a defect occurs here, all the microfabrication effort invested in the preceding stages is lost. Therefore, rigorous condition design for sacrificial layer etching is paramount.
What Is Stiction?
The "Adhesion" Phenomenon Where Microstructures Fail to Detach
Stiction is a phenomenon in which a MEMS microstructure unintentionally comes into contact with and adheres to the substrate or adjacent structures, becoming unable to detach using its own mechanical restoring force alone. It occurs both during fabrication and in-service operation, positioning it as a primary cause of yield loss in MEMS(Source:C. H. Mastrangelo, "Suppression of Stiction in MEMS").
Release Stiction vs. In-Use Stiction
Stiction is broadly categorized into two types based on when it occurs(Source:C. H. Mastrangelo, "Suppression of Stiction in MEMS").
-
Release Stiction: Occurs during the fabrication release process.
-
In-Use Stiction: Occurs during the actual operation of the completed device.
This article focuses on release stiction, which is directly tied to sacrificial layer etching. Because in-use stiction manifests during operation, reviewing only the release process may not fully resolve or isolate the issue.
Why MEMS Structures Are Prone to Stiction
Because MEMS structures feature an exceptionally high surface-area-to-volume ratio, surface forces become dominant(Source:Y. X. Zhuang、A. Menon, "On the Stiction of MEMS Materials"). Forces negligible in macroscopic components can scale up sufficiently to induce significant deformation and permanent adhesion in micro-scale structures.
Causes of Stiction During MEMS Sacrificial Layer Etching
Stiction takes place in two distinct phases: the force that pulls the microstructures together, and the force that prevents them from detaching once in contact. Because the former mechanism differs depending on the process method, let us examine wet etching and vapor HF etching separately.
Cause 1: Capillary Forces During Rinsing and Drying After Wet Etching
In conventional wet etching, the sacrificial layer is removed using chemical solutions such as hydrofluoric acid (HF), followed by deionized (DI) water rinsing and drying. During this drying stage, a liquid-vapor interface is formed. As the liquid evaporates, intense capillary forces and surface tension are generated within the narrow gaps, pulling the movable microstructure toward the substrate(Source:Y. X. Zhuang、A. Menon, "On the Stiction of MEMS Materials").
A key characteristic of this failure mode is that defects occur during drying even when etching itself proceeded without issue.
Cause 2: Condensation of "Product Water" in Vapor HF Processes
Vapor hydrofluoric acid (Vapor HF) etching removes sacrificial layers without liquid immersion baths or subsequent rinse-and-dry steps(Source:Y.-I. Lee et al., "Dry release for surface micromachining with HF vapor-phase etching").
However, the chemical reaction between SiO₂ and HF inherently produces water (H₂O) as a byproduct(Source:U.S. Patent US7365016B2,"Anhydrous HF release of process for MEMS devices"). When partial pressures of HF, water, and reaction byproducts are high, or when substrate temperature is too low, condensation conditions are established. The produced water—or intentionally added catalyst moisture—condenses, creating a localized wet state(Source:U.S. Patent US20050003669A1 ,"HF vapor phase cleaning and oxide etching").
This water condensation has been cited as a major reason past vapor HF releases failed(Source:Y.-I. Lee et al., "Dry release for surface micromachining with HF vapor-phase etching"). Once condensation occurs, capillary forces develop even in a vapor-phase process, triggering stiction anew.
If stiction persists despite switching to a vapor-phase process, it is worth verifying whether condensation conditions are being met due to component partial pressures or substrate temperature settings, rather than doubting the etching chemistry itself.
Why Detachment Fails Once Contact Is Made
Once structural surfaces make physical contact, forces such as van der Waals forces, hydrogen bonding, capillary condensation, and electrostatic attraction come into play. When these combined attractive forces exceed the structural mechanical restoring force, the microstructure cannot return to its free state, causing device failure(Source:Y. X. Zhuang、A. Menon, "On the Stiction of MEMS Materials").
In short, the fundamental countermeasure against stiction is "preventing initial contact." The critical design starting point is deciding where—in the drying step or the etching step—to eliminate the capillary forces that trigger this contact.
Two Additional Defects to Monitor Alongside Stiction in Vapor HF Processes
Stiction is not the only issue in vapor HF processes; moisture and reaction byproducts can induce secondary defects.
Corrosion of Aluminum Electrodes and Metal Layers
Failure to remove moisture vapor generated around the sacrificial layer can cause adverse effects on interconnect metals. It has been reported that non-anhydrous vapor HF severely corrodes aluminum (Al), titanium (Ti), and copper (Cu) layers(Source:U.S. Patent US7365016B2, "Anhydrous HF release of process for MEMS devices"). In monolithic MEMS devices integrating CMOS circuits and MEMS on a single substrate, aluminum corrosion constitutes a fatal flaw(Source:VTT「Studies on aluminium corrosion during and after HF vapour treatment」).
Both stiction and corrosion are strongly governed by moisture and condensation conditions. Optimizing process parameters based solely on one issue risks overlooking the other when exposed metallic layers are present.
Fluorinated Residues on Silicon Nitride Layers
Silicon nitride (SiN) is widely used as an etch-stop layer or a structural passivation layer. However, it has been reported that vapor HF can react with the SiN layer to form fluorinated byproducts, such as ammonium fluorosilicate, which roughen the surface. When exposed to moist air, these byproducts become unstable and can transform into residues that cannot be removed even by thermal annealing. The same patent discloses an embodiment in which, without exposing the wafer to the atmosphere post-release, the byproducts are removed in situ under vacuum conditions of less than approximately 40 Torr and above approximately 100°C(Source:U.S. Patent US7365016B2, "Anhydrous HF release of process for MEMS devices").
When designing devices that utilize SiN as an etch-stop, it is critical to evaluate not only the etch selectivity against SiO₂, but also the byproduct removal conditions and the precise timing of atmospheric exposure.
Stiction Countermeasure Options and Prerequisites
Representative countermeasures against release stiction include eliminating the liquid-gas interface during drying, utilizing sublimation techniques, and employing dry vapor-phase release without liquid baths.
| Objective | Key Prerequisites & Considerations | |
|---|---|---|
| Supercritical CO₂ Drying | Eliminates the liquid-gas interface during drying to prevent capillary forces. | Requires dedicated high-pressure equipment. Mass-production throughput depends heavily on tool configuration. |
| Sublimation-Based Methods | Temporarily supports structures with a sacrificial scaffold, which is then removed via sublimation. | Procedures and recipes vary substantially depending on the chosen chemistry. |
| Vapor HF Release | Eliminates sacrificial layers without liquid chemical baths or post-etch rinse/dry steps. | Demands strict parameter control to prevent condensation of reaction-product water. |
Supercritical CO₂ Drying: Eliminates Interfaces but Introduces Equipment Overhead
Supercritical CO₂ drying (Critical Point Drying: CPD) subjects carbon dioxide to conditions above its critical point (31.1°C, 73.8 bar), drying without ever crossing a phase boundary between liquid and vapor. This prevents structural collapse caused by surface tension(Source:Cornell NanoScale Facility, "Critical Point Dryer").
Conversely, this approach necessitates dedicated pressure vessels and high-pressure pumps. High equipment costs and batch-processing constraints often represent adoption hurdles(Source:Microelectronic Engineering, "An overview of supercritical CO2 applications in microelectronics processing"). Furthermore, some cite drawbacks for mass production due to manual, single-wafer loading into heavy-walled, high-pressure chambers(Source:U.S. Patent US7365016B2, "Anhydrous HF release of process for MEMS devices"). Practical throughput and equipment burdens depend on chamber capacity and automation level. When considering high-volume manufacturing, equipment cost and throughput must be evaluated alongside stiction prevention efficiency.
Sublimation Methods: Employing Temporary Solid Supports
Stiction suppression using sublimation has also been actively researched. One reported low-cost method involves depositing camphor beneath suspended microstructures as a temporary support material, which is subsequently sublimated away by heating(Source:IEEE MEMS 2020, "MEMS Stiction Suppression Using Low-Stress Camphor Sublimation"). Sublimation approaches encompass multiple chemistries, each with varying steps and process windows.
Vapor HF Release: Condensation Control Is Essential
Vapor HF etching achieves bathless release without high-pressure equipment like that required in supercritical drying. As discussed under Cause 2, success with this method hinges on preventing the condensation of generated reaction water.
Selecting the Method Based on Sacrificial Layer Material
Vapor release processes depend strictly on the choice of sacrificial material:
-
Silicon Sacrificial Layers: A non-plasma, isotropic dry etch using xenon difluoride (XeF₂) gas is common. This approach exhibits exceptionally high selectivity over SiO₂ and SiN (Source:MIT, "XeF2 isotropic etching of silicon").
-
Silicon Dioxide Sacrificial Layers: A tightly controlled, anhydrous vapor HF process is required.
When planning countermeasures, the first step is to clarify the material composition of your device's sacrificial layer.
The Key to Preventing Stiction in Vapor HF: "Zero Condensation"
Combining Anhydrous HF with Alcohol Vapors
When removing a SiO₂ sacrificial layer with vapor HF, minimizing moisture generation and presence is paramount. A proven solution is a gas-phase process combining anhydrous hydrogen fluoride (Anhydrous HF) and alcohol vapor. Using a low-pressure mixture of anhydrous HF and methanol successfully resolves water condensation issues(Source:Y.-I. Lee et al., "Dry release for surface micromachining with HF vapor-phase etching"). Alcohol additives serve to suppress the condensation of reaction-generated water vapor on microstructure surfaces(Source:U.S. Patent US7365016B2, "Anhydrous HF release of process for MEMS devices").
The Sub-Monolayer Adsorption Concept
As another operational approach, a U.S. patent employing anhydrous HF and water vapor details specific conditions: wafer temperature and partial pressures of HF and water vapor are regulated such that surface coverage of reactants on oxide adsorption sites remains below 95%—within the sub-monolayer regime(Source:U.S. Patent US20050003669A1, "HF vapor phase cleaning and oxide etching"). The core philosophy is driving the reaction just below the threshold where a liquid phase can nucleate, thereby extinguishing the root cause of capillary action. (Note: This figure is defined for that specific patented process and is not a universal parameter for all vapor HF processes, including alcohol-assisted variants).
Under either framework, optimal recipe windows shift depending on structural dimensions. Process conditions must be tuned specifically to structural geometry and undercut release length.
Checklist for Preventing Recurring Stiction Defects
If stiction occurs during release, first verify the sacrificial layer material and current release method. Then, review the following parameters to systematically isolate root causes:
-
Sacrificial Layer Material & Release Mode: Identify whether the material is Si or SiO₂ , and whether wet or vapor-phase etching is employed. The material choice fundamentally dictates the compatible vapor release chemistry.
-
Rinsing & Drying in Wet Etching: Verify whether capillary forces generated at the liquid-vapor interface during drying induce structural collapse.
-
Condensation Conditions in Vapor HF: Ensure that partial pressures and substrate temperatures are controlled to prevent localized moisture condensation on the surface.
-
Exposed Metal Layers: For architectures with exposed aluminum interconnects, evaluate corrosion risks concurrently under humid and condensing conditions.
-
SiN Byproducts: When utilizing silicon nitride as an etch-stop layer, confirm that fluorinated residues are thoroughly desorbed before exposure to atmosphere.
- Structural Geometry: Optimize etch recipe parameters in accordance with the mechanical stiffness, gap height, and undercut release length of the suspended structure.
Stiction failures rarely stem from a single variable. In vapor HF, for instance, localized condensation dramatically elevates both stiction and metal corrosion risks at the same time.
Summary
-
Stiction is the unintended adhesion of microstructures that prevents recovery; occurring during both release and operation, it is a dominant cause of MEMS yield fallout.
-
In wet processes, capillary forces at the liquid-gas interface during rinsing and drying serve as the primary trigger.
-
In vapor HF processes, improper control of partial pressures or substrate temperature causes generated water to condense, reviving stiction risks. Structures containing aluminum require simultaneous corrosion evaluation.
-
Countermeasure options include supercritical CO₂ drying, sublimation-based release, and dry vapor-phase etching, each carrying distinct tool, operational, and process management prerequisites.
-
In vapor HF etching of SiO₂ , the absolute key is "preventing condensation" by utilizing alcohol co-reactants and precisely regulating temperature and partial pressures.
Stiction is a manageable defect when addressed by isolating root causes across individual process steps. If stiction arises, start by re-verifying sacrificial layer materials and release methodologies. Then, optimize rinse/dry parameters for wet setups, or tune partial pressures and substrate temperatures for vapor HF equipment.
Sacrificial Layer Etching Technologies from Sumitomo Precision Products
As part of its MEMS etch equipment portfolio, Sumitomo Precision Products offers the "Vetelgeuse" sacrificial layer etching system, engineered specifically for SiO₂ sacrificial layer release. Key features include:
-
Proprietary vapor-phase etching technology combining anhydrous HF and alcohol vapor.
-
Selective removal of oxide layers without corrosion or structural damage, even on devices incorporating aluminum interconnects.
-
A completely dry process producing no chemical liquid waste.
-
Compatibility across diverse undercut lengths, ranging from micrometer-scale microstructures to millimeter-scale cavities.
-
Built on the "VPX" platform, a 3-chamber configuration supporting 200 mm wafers designed for small-to-medium volume manufacturing and R&D.
Demonstrated application examples include infrared bolometer architectures, cantilevers, SOI wafer BOX layer release, and silicon oscillator release provided by commercial MEMS timing device manufacturers.